Paper Corner Applicator With Rotary Arm Pallet Wrapper
This is best choice for pallet with corrugated paper board. The wrapping can be set on top part of pallet, leaving the bottom not wrapped to save time and cost.
The wrapping realize dust-proof, moisture-proof, less packaging cost, improve packing efficiency, and reduce product loss in transportation.
Paper corner applicator with rotary arm pallet wrapper is a multi-functional system. It applies paper corner on pallet 4 sides when wrapping. The main wrapper has a film cut and clamp unit on top of pallet. The cut unit pressed down onto pallet as top-press unit to hold pallet when wrapping.
This is best choice for pallet with corrugated paper board. The wrapping can be set on top part of pallet, leaving the bottom not wrapped to save time and cost.
The wrapping realize dust-proof, moisture-proof, less packaging cost, improve packing efficiency, and reduce product loss in transportation.
Technology data:
Max load size(mm) | 1200 (L)×1200(W) ×1600(H)mm |
Conveyor height | 500mm |
Packing efficiency | 0-40 loads / hour |
Rotary arm speed | 0-15rpm |
Power supply | 2.5 KW 380V 50HZ 3Phase |
Max load capacity | 2000kgs, depending on the conveyor |
Wrapping requirement | Bottom wrapping starting from 2/3 of pallet, top wrapping 15cm higher than the height of pallet |
Working ambiance | Indoor, normal temperature |
Wrapping material:
Utility:
Compressed air
Pressure: 0.5-0.7 MPa
Dew point: +2-+10℃ (7bar, +2-+10℃)
Filter: 40 µm
Air quality: oil and water free air
Air consumption: 1000ml/min
Power supply: 380V (+/- 10%)/3phase/50Hz (+/- 1Hz)
Power installed: ≈2.5kw
Supply scope
Machine main frame 1set
Gantry type frame, made of square steel tube, material: Q235 steel
Driving motor base is installed on the frame
The rotary arm are fixed on the frame connecting with slew bearing
Frame size: (to be confirmed by drawing)
Driving device for rotary arm 1set
Frequency control motor with brake, power rated: 1.5KW
Rotary arm speed: n=15rpm (frequency motor with brake)
Two position limits equipped on two ends of rotary arm
Film carriage 1 set
Open-door type pre-stretch film carriage, stretch ratio 200% (1m to 3m)
Film carriage lifting driving: chain driving, good stability and high reliability
Driving reducer: worm gear reducer
Motor power: 0.37kw
Film carriage delivery device 1set
The photoelectric switch is installed on the film carriage, automatic detect the height of the pallet
Driving motor: AC motor, speed adjustable
Power rated of film delivery driving motor: 0.37KW
Film delivery following up mechanism
The film delivery following up the rotary arm rotating, the proximity switch control the start/stop of film delivery motor to follow up the rotary arm
Film auto feeding and cutting device 1set
When stretch wrapping finish, the film will be cut and clamped automatically.
When the film tail is released from the clamp, the air shooter will blow the film tail up, then the film tail will be wrapped by stretch film and keep it tightly with the pallet to ensure no film tail produced.
Film hot melt cutting adopts electrical heating wire to cut the film.
After film being cut, the hot sealer will seal the film tail automatically to ensure no film tail come out.
Paper corner applicator 4sets
The applicator can sense the position of the pallet, and then adjust the position of the installation. The working center should be same as the wrapper.
Auto sense the paper board quantity and alarm when lack of material, so that the paper boards can be feed manually;
The paper board should be in same level without angle;
Paper corner magazine 2pcs for each applicator, feed the paper board vertically;
The device should be connected with the main wrapper so that whole system work automatically;
The buyer should provide the exact specification of the paper board for confirmation. The positioning of the paper board should be based on the bottom line of the board.
Specification of the paper board
Paper corner dimension: W50mm×thickness5mm;
Paper corner height: ≤1500mm;
Angle: 90±1°
Pneumatic control system 1set
Air source required: the compressed air shall be supplied by end user to the inlet of the stop valve.
The pneumatic cylinder is controlled by control box.
Safety interlock device 1set
Start-up of the rotary arm & conveyor
The safety fence has the function of power cut when the door be opened. (For option of safeguard fence)
Electrical control system 1set
PLC control system, the wrapping layers, the wrapping cycles, and the time of top wrapping.
8 programs can be set in the PLC system for different packing options.
The safety command can be added on the control program, add PLC extension module to ensure the safety of the machine.
The operating parameter can be set on Siemens touch screen, more convenient for operation.
Photo eye will detect the height of the pallet automatically.
Slewing bearing driving the rotary arm, high precision positioning.
The driving speed of rotary arm, roll conveyor, film carriage lifting are adjustable individually, the film delivery speed is also adjustable, equipped alarm for film break.
The wrapping machine is powered with pause/manual/automatic wrapping switch function, in order to ensure the better operating.
The machine is equipped with running warning light.
The machine is equipped with Ethernet interface, used for outputting the related information of the wrapping machine (Include the production quantity, mechanical efficiency, fault information etc.)
